<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=us-ascii">
<META content="MSHTML 6.00.2800.1619" name=GENERATOR></HEAD>
<BODY>
<DIV><SPAN class=062551108-11022009><FONT face=Arial
size=2>Hi,</FONT></SPAN></DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial size=2>I installed the
EtherCAT master stack 1.5, configerd it with proper MAC address and it seems to
have troubles starting.</FONT></SPAN></DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial size=2>I'm confused about
different state messages -> please see outputs below:</FONT></SPAN></DIV>
<DIV><SPAN class=062551108-11022009></SPAN><SPAN
class=062551108-11022009></SPAN><SPAN class=062551108-11022009><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=062551108-11022009><SPAN class=062551108-11022009><FONT
face=Arial
size=2>--------------------------------------------------------------------------------------------------------------------------------</FONT></SPAN></SPAN></DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial size=2>>
dmesg<BR>EtherCAT: Master driver devel r1655<BR>EtherCAT: 1 master waiting for
devices.<BR>ACPI: PCI interrupt for device 0000:06:04.0 disabled<BR>ec_8139too
EtherCAT-capable Fast Ethernet driver 0.9.28, master devel r1655<BR>ACPI: PCI
Interrupt 0000:06:04.0[A] -> GSI 19 (level, low) -> IRQ 18<BR>eth1:
RealTek RTL8139 at 0xf8df4c00, 00:02:44:68:9e:33, IRQ 18<BR>eth1:
Identified 8139 chip type 'RTL-8139C'<BR>udev: renamed network interface eth1 to
eth3</FONT></SPAN></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV><SPAN class=062551108-11022009>
<DIV><BR><FONT face=Arial size=2>> /opt/etherlab/bin/ethercat
master<BR>Master0<BR> Phase: Waiting for device...<BR> Slaves:
0<BR> Device0: a2:ff:02:5d:a9:84 (waiting...)<BR> Tx
count: 0<BR> Rx count: 0<BR> Device1: None.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>> /etc/init.d/ethercat status<BR>Checking for
EtherCAT master devel <BR>Master0 dead</FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN
class=062551108-11022009>--------------------------------------------------------------------------------------------------------------------------------</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial size=2>looking forward for
any help!</FONT></SPAN></DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial
size=2>thanks,</FONT></SPAN></DIV>
<DIV><SPAN class=062551108-11022009><FONT face=Arial
size=2>Clemens</FONT></SPAN></SPAN></DIV></BODY></HTML>
<pre>Important Notice:
This electronic transmission (including any attachments) is intended solely for the use and information
of the addressee(s). It may contain confidential or legally privileged information. Any unauthorized use
or disclosure of this message is strictly prohibited.If you are not the intended recipient, please notify
the sender immediately and delete the message and its attachments.
The sender does not guarantee the integrity of this transmission and shall therefore never be liable if
the message is altered or falsified nor for any virus, interception or damage to your system.