[etherlab-dev] Etherlab master looses mailbox configuration during client connection loss

[Christoph Schroeder]

Hi Gavin,

thanks for your answer. The "Mailbox configuration" debug message hint
was a good idea. I found that the mailboxes aren't configured at all
during recovery of the slave. I looked up in the master code and found
that in the fsm_slave_scan.c some things are only done if the slave
supports CoE. Maybe this is a little odd configuration, but our slave is
a custom slave which only supports VoE! I attached a patch (applied to
the top of the current unofficial patchset) that fixed the issue for me.
Not sure if this is the correct way to fix it though, so someone who is
more familar with the master code should have a look at it. Maybe this
is also relevant for other Mailbox protocols. The master shouldn't
assume that mailboxes are only used if CoE is supported. I would
appreciate it if a fix can be added to the patchset in the future.

Best regards,
Christoph


On 09/21/2017 01:37 AM, Gavin Lambert wrote:
> The size in ecrt_slave_config_create_voe_handler specifies the maximum size of the VoE request/reply, which is different from (but must be equal or smaller than) the actual mailbox size.
>
> The mailbox size itself is specified by the slave's SII data, as read from its EEPROM during the INIT -> PREOP transition.  If the slave reboots or once communications are restored it will be reconfigured (which involves redoing the INIT -> PREOP transition), but that shouldn't change the sizes unless there's a bug in the slave itself.
>
> It's possible you're running into some kind of timing error, where it's somehow trying to execute the VoE request before the slave has properly re-entered PREOP or higher, although I thought that such cases are prevented in the unofficial patchset at least.  My application code does perform an additional sanity check before executing requests though so it's possible I missed a corner case if that is omitted.
>
> Try running your test again with "ethercat debug 1" in effect and look at the syslog.  In particular look for log messages starting with "Mailbox configuration"; this is where it reports the detected mailbox sizes that are later used in the error message below.  Also check in what order things are happening with regard to when you're interrupting the slave and when the VoE request tries to execute and generates the error.
>
>> -----Original Message-----
>> From: Christoph Schröder
>> Sent: Thursday, 21 September 2017 03:09
>> To: etherlab-dev at etherlab.org
>> Subject: [etherlab-dev] Etherlab master looses mailbox configuration during
>> client connection loss
>>
>> Hi All,
>>
>> I encountered a problem with the recovery abilities of the Etherlab master
>> after connection loss (e.g. pull out cable of one slave and plug it in again). The
>> master seems to reset the mailbox configuration. If I start a VoE-request I get
>> the following kernel message:
>> [132256.054043] EtherCAT ERROR 0-main-0: Data size (24) does not fit in
>> mailbox (0)!
>>
>> The mailbox size configured through ecrt_slave_config_create_voe_handler
>> seems to be lost and not only for the slave disconnected, but also for the
>> slave that never lost it's connection (tested with 2). This happens with and
>> without the newest inofficial patchset (20170914).
>>
>> This seems to be a bug as ecrt_slave_config_create_voe_handler has to be
>> called before ecrt_master_activate, so recreation of the config after
>> recovery of the connection is not possible.
>>
>> Without connection loss everything works fine, but we would like to make
>> the system as robust as possible without the need to restart the application.
>> Does anyone has an idea how to fix this or can someone at least explain what
>> happens during a connection loss and recovery resp.
>> which functions are called by the master?
>>
>>
>> Thanks and best regards,
>> Christoph
>>
>> ________________________________
>>
>> Helmholtz-Zentrum Berlin für Materialien und Energie GmbH
>>
>> Mitglied der Hermann von Helmholtz-Gemeinschaft Deutscher
>> Forschungszentren e.V.
>>
>> Aufsichtsrat: Vorsitzender Dr. Karl Eugen Huthmacher, stv. Vorsitzende Dr.
>> Jutta Koch-Unterseher
>> Geschäftsführung: Prof. Dr. Bernd Rech (kommissarisch), Thomas Frederking
>>
>> Sitz Berlin, AG Charlottenburg, 89 HRB 5583
>>
>> Postadresse:
>> Hahn-Meitner-Platz 1
>> D-14109 Berlin
>>
>> http://www.helmholtz-berlin.de
>> _______________________________________________
>> etherlab-dev mailing list
>> etherlab-dev at etherlab.org
>> http://lists.etherlab.org/mailman/listinfo/etherlab-dev


________________________________

Helmholtz-Zentrum Berlin für Materialien und Energie GmbH

Mitglied der Hermann von Helmholtz-Gemeinschaft Deutscher Forschungszentren e.V.

Aufsichtsrat: Vorsitzender Dr. Karl Eugen Huthmacher, stv. Vorsitzende Dr. Jutta Koch-Unterseher
Geschäftsführung: Prof. Dr. Bernd Rech (kommissarisch), Thomas Frederking

Sitz Berlin, AG Charlottenburg, 89 HRB 5583

Postadresse:
Hahn-Meitner-Platz 1
D-14109 Berlin

http://www.helmholtz-berlin.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 0072-Fix-VoE-Mailbox-config.patch
Type: text/x-patch
Size: 1717 bytes
Desc: not available
URL: <http://lists.etherlab.org/pipermail/etherlab-dev/attachments/20170921/89ec7906/attachment.bin>