[etherlab-users] "Invalid mailbox configuration", how to configure?

[Stefan Löfgren]

Ahhh... I'm sorry...
I did not realize that the debug output was there... ;)
That explains things... Here it is:

/Stefan

EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 136k freed
EXT3 FS on hda1, internal journal
EtherCAT: Master driver 1.4.0-pre trunk r1088
EtherCAT: 1 master waiting for devices.
EtherCAT: Master debug level set to 1.
ec_8139too EtherCAT-capable Fast Ethernet driver 0.9.27, master 1.4.0-pre
trunk r1088
PCI: Found IRQ 9 for device 0000:00:02.0
EtherCAT DEBUG: Master 0 declined device 00:D0:C9:97:05:E7.
eth0: RealTek RTL8139 at 0xc000, 00:d0:c9:97:05:e7, IRQ 9
eth0:  Identified 8139 chip type 'RTL-8139C'
PCI: Found IRQ 9 for device 0000:00:09.0
EtherCAT: Accepting device 00:D0:C9:97:05:E6 for master 0.
ec0: RealTek RTL8139 at 0xd000, 00:d0:c9:97:05:e6, IRQ 9
ec0:  Identified 8139 chip type 'RTL-8139C'
EtherCAT: Link state changed to UP.
EtherCAT: Starting master thread.
EtherCAT: 1 slave responding.
EtherCAT: Slave states: PREOP.
EtherCAT DEBUG: Clearing station addresses...
EtherCAT: Scanning bus.
EtherCAT DEBUG: Found Sync manager category with 1 sync managers.
EtherCAT DEBUG: Total sync managers: 1.
EtherCAT DEBUG: Found Sync manager category with 1 sync managers.
EtherCAT DEBUG: Total sync managers: 2.
EtherCAT DEBUG: Found Sync manager category with 1 sync managers.
EtherCAT DEBUG: Total sync managers: 3.
EtherCAT DEBUG: Found Sync manager category with 1 sync managers.
EtherCAT DEBUG: Total sync managers: 4.
EtherCAT DEBUG: Scanning Pdo mapping/configuration of slave 0.
EtherCAT DEBUG: Processing dir 0 of slave 0.
EtherCAT DEBUG: Reading Pdo mapping of sync manager 2 of slave 0.
EtherCAT DEBUG: Uploading Sdo 0x1C12:0 from slave 0.
EtherCAT DEBUG: Upload request:
EtherCAT DEBUG: 00 20 40 12 1C 00 00 00 00 00
EtherCAT ERROR: Mailbox error response received from slave 0 - Code 0x0004:
"MBXERR_SERVICENOTSUPPORTED".
EtherCAT DEBUG: 01 00 04 00
EtherCAT ERROR: Failed to read number of mapped Pdos from slave 0.
EtherCAT: Bus scanning completed in 26 ms.
EtherCAT DEBUG: Reconfiguring slave 0 (PREOP).
EtherCAT DEBUG: Configuring slave 0...
EtherCAT DEBUG: Slave 0 is now in INIT.
EtherCAT DEBUG: Clearing FMMU configurations of slave 0...
EtherCAT DEBUG: Configuring mailbox sync managers of slave 0.
EtherCAT DEBUG: SM0: Addr 0x1800, Size  20, Ctrl 0x26, En 1
EtherCAT DEBUG: SM1: Addr 0x1832, Size  20, Ctrl 0x22, En 1
EtherCAT DEBUG: Slave 0 is now in PREOP.
EtherCAT DEBUG: Finished configuration of slave 0.
EtherCAT DEBUG: Fetching Sdo dictionary from slave 0.
EtherCAT ERROR: Mailbox error response received from slave 0 - Code 0x0002:
"MBXERR_UNSUPPORTEDPROTOCOL".
EtherCAT DEBUG: 01 00 02 00



---------- Original Message -----------
From: Florian Pose <fp at igh-essen.com>
To: etherlab-users at lists.etherlab.org
Sent: Tue, 18 Mar 2008 12:22:14 +0100
Subject: Re: [etherlab-users] "Invalid mailbox configuration", how to	configure?

> Hello again,
> 
> On Tue, Mar 18, 2008 at 08:43:40AM +0100, Stefan Löfgren wrote:
> > Mar 18 09:54:16 lablinux kernel: EtherCAT ERROR: Mailbox error response
> > received from slave 0 - Code 0x0004: "MBXERR_SERVICENOTSUPPORTED".
> > Mar 18 09:54:16 lablinux kernel: EtherCAT ERROR: Failed to read number of
> > mapped Pdos from slave 0.
> > Mar 18 09:54:16 lablinux kernel: EtherCAT ERROR: Mailbox error response
> > received from slave 0 - Code 0x0002: "MBXERR_UNSUPPORTEDPROTOCOL".
> 
> I'm not really sure about the time this happens. Could you please supply
> the kernel messages (output of 'dmesg') around this error with
> debugging set to 1?
> 
> -- 
> Best regards,
> Florian Pose
> 
> http://etherlab.org
> _______________________________________________
> etherlab-users mailing list
> etherlab-users at lists.etherlab.org
> http://lists.etherlab.org/mailman/listinfo/etherlab-users
------- End of Original Message -------