[etherlab-users] EL6751 SDO-Configuration
Matze Thias
matze.thiasm at gmail.com
Fri Jan 22 14:17:59 CET 2016
Thank you Thomas for sharing your code :) In my code I'm doing almost the
same, except that I do encode the configuration bytes directly in an array
instead of converting it from a string.
Also I do not have to configure CANOpen-Slaves. The only slave listening on
the CAN-Bus expects "raw"(Layer2)-CAN-Messages and do not understand the
higher-level CANOpen-Protocol. When I configure it that way, I always get
EtherCAT ERROR 0-1: Failed to set SAFEOP state, slave refused state change
(PREOP + ERROR).
EtherCAT ERROR 0-1: Unknown AL status code 0xF101
PS: I just dumped the device info via ethercat slaves -v. I got:
General:
Group: Communication
Image name:
Order number: EL6751
Device name: EL6751 CANopen Master
CoE details:
Enable SDO: yes
Enable SDO Info: yes
Enable PDO Assign: no
Enable PDO Configuration: no
Enable Upload at startup: no
Enable SDO complete access: yes
Flags:
Enable SafeOp: no
Enable notLRW: no
Current consumption: 300 mA
So flags are saying, that SafeOp is not enabled. Does that mean that SafeOP
does not exist? Considering the error message is there any correlation? How
can I fix this?
2016-01-20 12:44 GMT+01:00 Thomas Paoloni <thomas at digithom.it>:
> Hi,
>
> Sometimes a piece of code is better than explanations ...
> Here is mine, which configures the PDO of the CanOpen side on my EL6731
>
> static int err_code;
> static int cnt;
> static int x, y, z, i, num_config_lines;
> static char app_str[1024];
> static unsigned char pb_config_buf[2048];
> static int ecrt_retval;
> uint32_t value_to_write;
> uint32_t abort_code;
>
> struct config_item {
> unsigned int slave_pos;
> unsigned short address;
> char * config_string;
> };
>
> // 6 Atos Hydraulic valves without rxpdo2
> const config_item config [] = {
>
> // EL67xx CoE Init Cmd 2 (F800:00)
> {19, 0xF800, "11 00 7F 06 80 00 10 27 00 00 00 00 00 00 00 1E 64
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00"},
> // EL67xx CoE Init Cmd 3 (8000:00)
> {19, 0x8000, "2E 00 01 00 98 01 00 07 F4 00 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 00 03 00 D0 07
> D0 07 05 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 4 (8006:00)
> {19, 0x8006, "03 00 81 01 00 00 FF 02 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 5 (8008:00)
> {19, 0x8008, "04 00 01 02 00 00 FF 02 00 00 00 00 00 00 01 03 00
> 00 FF 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 6 (8003:00)
> {19, 0x8003, "0E 00 00 18 01 04 00 81 01 00 00 00 18 02 01 00 FF
> 01 18 01 04 00 81 03 00 00 01 18 02 01 00 FF 02 18 01 04 00 81 04 00 00 02
> 18 02 01 00 FF 00 14 01 04 00 01 02 00 00 00 14 02 01 00 FF 01 14 01 04 00
> 01 03 00 00 01 14 02 01 00 FF 02 14 01 04 00 01 04 00 00 02 14 02 01 00 FF
> 03 14 01 04 00 01 05 00 00 03 14 02 01 00 FF"},
> // EL67xx CoE Init Cmd 7 (8010:00)
> {19, 0x8010, "2E 00 02 00 98 01 00 07 F4 00 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 00 03 00 D0 07
> D0 07 05 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 8 (8016:00)
> {19, 0x8016, "03 00 82 01 00 00 FF 02 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 9 (8018:00)
> {19, 0x8018, "04 00 02 02 00 00 FF 02 00 00 00 00 00 00 02 03 00
> 00 FF 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 10 (8013:00)
> {19, 0x8013, "0E 00 00 18 01 04 00 82 01 00 00 00 18 02 01 00 FF
> 01 18 01 04 00 82 03 00 00 01 18 02 01 00 FF 02 18 01 04 00 82 04 00 00 02
> 18 02 01 00 FF 00 14 01 04 00 02 02 00 00 00 14 02 01 00 FF 01 14 01 04 00
> 02 03 00 00 01 14 02 01 00 FF 02 14 01 04 00 02 04 00 00 02 14 02 01 00 FF
> 03 14 01 04 00 02 05 00 00 03 14 02 01 00 FF"},
> // EL67xx CoE Init Cmd 11 (8020:00)
> {19, 0x8020, "2E 00 03 00 98 01 00 07 F4 00 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 00 03 00 D0 07
> D0 07 05 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 12 (8026:00)
> {19, 0x8026, "03 00 83 01 00 00 FF 02 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 13 (8028:00)
> {19, 0x8028, "04 00 03 02 00 00 FF 02 00 00 00 00 00 00 03 03 00
> 00 FF 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 14 (8023:00)
> {19, 0x8023, "0E 00 00 18 01 04 00 83 01 00 00 00 18 02 01 00 FF
> 01 18 01 04 00 83 03 00 00 01 18 02 01 00 FF 02 18 01 04 00 83 04 00 00 02
> 18 02 01 00 FF 00 14 01 04 00 03 02 00 00 00 14 02 01 00 FF 01 14 01 04 00
> 03 03 00 00 01 14 02 01 00 FF 02 14 01 04 00 03 04 00 00 02 14 02 01 00 FF
> 03 14 01 04 00 03 05 00 00 03 14 02 01 00 FF"},
> // EL67xx CoE Init Cmd 15 (8030:00)
> {19, 0x8030, "2E 00 04 00 98 01 00 07 F4 00 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 00 03 00 D0 07
> D0 07 05 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 16 (8036:00)
> {19, 0x8036, "03 00 84 01 00 00 FF 02 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 17 (8038:00)
> {19, 0x8038, "04 00 04 02 00 00 FF 02 00 00 00 00 00 00 04 03 00
> 00 FF 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 18 (8033:00)
> {19, 0x8033, "0E 00 00 18 01 04 00 84 01 00 00 00 18 02 01 00 FF
> 01 18 01 04 00 84 03 00 00 01 18 02 01 00 FF 02 18 01 04 00 84 04 00 00 02
> 18 02 01 00 FF 00 14 01 04 00 04 02 00 00 00 14 02 01 00 FF 01 14 01 04 00
> 04 03 00 00 01 14 02 01 00 FF 02 14 01 04 00 04 04 00 00 02 14 02 01 00 FF
> 03 14 01 04 00 04 05 00 00 03 14 02 01 00 FF"},
> // EL67xx CoE Init Cmd 19 (8040:00)
> {19, 0x8040, "2E 00 05 00 98 01 00 07 F4 00 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 00 03 00 D0 07
> D0 07 05 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 20 (8046:00)
> {19, 0x8046, "03 00 85 01 00 00 FF 02 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 21 (8048:00)
> {19, 0x8048, "04 00 05 02 00 00 FF 02 00 00 00 00 00 00 05 03 00
> 00 FF 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 22 (8043:00)
> {19, 0x8043, "0E 00 00 18 01 04 00 85 01 00 00 00 18 02 01 00 FF
> 01 18 01 04 00 85 03 00 00 01 18 02 01 00 FF 02 18 01 04 00 85 04 00 00 02
> 18 02 01 00 FF 00 14 01 04 00 05 02 00 00 00 14 02 01 00 FF 01 14 01 04 00
> 05 03 00 00 01 14 02 01 00 FF 02 14 01 04 00 05 04 00 00 02 14 02 01 00 FF
> 03 14 01 04 00 05 05 00 00 03 14 02 01 00 FF"},
> // EL67xx CoE Init Cmd 23 (8050:00)
> {19, 0x8050, "2E 00 06 00 98 01 00 07 F4 00 00 00 02 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 00 03 00 D0 07
> D0 07 05 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 24 (8056:00)
> {19, 0x8056, "03 00 86 01 00 00 FF 02 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 25 (8058:00)
> {19, 0x8058, "04 00 06 02 00 00 FF 02 00 00 00 00 00 00 06 03 00
> 00 FF 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00"},
> // EL67xx CoE Init Cmd 26 (8053:00)
> {19, 0x8053, "0E 00 00 18 01 04 00 86 01 00 00 00 18 02 01 00 FF
> 01 18 01 04 00 86 03 00 00 01 18 02 01 00 FF 02 18 01 04 00 86 04 00 00 02
> 18 02 01 00 FF 00 14 01 04 00 06 02 00 00 00 14 02 01 00 FF 01 14 01 04 00
> 06 03 00 00 01 14 02 01 00 FF 02 14 01 04 00 06 04 00 00 02 14 02 01 00 FF
> 03 14 01 04 00 06 05 00 00 03 14 02 01 00 FF"},
> // download pdo 0x1C12 index
> {19, 0x1C12, "06 00 00 16 01 16 02 16 03 16 04 16 05 16"},
> // download pdo 0x1C13 index
> {19, 0x1C13, "0A 00 00 1A 01 1A 02 1A 03 1A 04 1A 05 1A 81 1A 82
> 1A 83 1A 84 1A"}
> };
>
> num_config_lines = sizeof(config)/sizeof(config_item);
>
> for (x=0 ; x<num_config_lines ; x++ ) {
> cout << "Downloading obj " << config[x].address << " " <<
> config[x].config_string << " \n";
> y=0;
> for (z=0 ; z<strlen(config[x].config_string) ; z++) if
> (config[x].config_string[z] != ' ') app_str[y++]=config[x].config_string[z];
>
> app_str[y]='\0';
> cnt = strToCharArray(app_str, pb_config_buf);
> if ((err_code =
> ecrt_slave_config_complete_sdo(slave_config_list[config[x].slave_pos],
> config[x].address, pb_config_buf, cnt)) != 0) {
> // if ((err_code = ecrt_slave_config_complete_sdo(config[x].slave_pos,
> config[x].address, pb_config_buf, cnt)) != 0) {
> cout << "Object configuration failed " << config[x].address << "
> Errocode = " << err_code << "\n";
> cout << "Data is: " << pb_config_buf << "\n";
> cout << "Data size is: " << cnt << "\n";
> exit(-1);
> } else {
> cout << "Downloading obj " << config[x].address << " " << app_str
> << " OK\n";
>
> }
> }
>
>
> On 19/01/2016 16:05, Matze Thias wrote:
>
> Hello,
>
> I am trying to configure the EL6751 at the moment, so that I am able to
> send raw CAN messages over ethercat(
> http://infosys.beckhoff.com/content/1033/el6751/html/el6751_layer2_statemachine.htm?id=10857
> ).
> I took the configuration, which is done in terms of sdo-startup-downloads,
> from one of the twincat dialogs. Which method for sdo configuration is the
> right to choose?
>
> If I use ecrt_master_sdo_download_complete for the different SDO-Objects
> to upload, nothing happens. When using ecrt_slave_config_complete_sdo the
> device error-led starts blinking(indicating, that some configuration is in
> progress) but at the same time I get this:
>
> Jan 19 15:50:06 e-node8 kernel: [611927.053364] EtherCAT ERROR 0-1: Failed
> to set SAFEOP state, slave refused state change (PREOP + ERROR).
> Jan 19 15:50:06 e-node8 kernel: [611927.059801] EtherCAT ERROR 0-1:
> Unknown AL status code 0xF101.
>
> Can anyone explain the error and has a solution for this? Maybe someone
> has experience in getting the el6751 configured and work-ready for this
> scenario and can share his insights :) ?
>
> Greetings,
>
> Matze Thias
>
>
>
> _______________________________________________
> etherlab-users mailing listetherlab-users at etherlab.orghttp://lists.etherlab.org/mailman/listinfo/etherlab-users
>
>
>
> _______________________________________________
> etherlab-users mailing list
> etherlab-users at etherlab.org
> http://lists.etherlab.org/mailman/listinfo/etherlab-users
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.etherlab.org/pipermail/etherlab-users/attachments/20160122/44edd1bc/attachment-0003.htm>
More information about the Etherlab-users
mailing list