[Etherlab-users] AKD drive Failed to set SAFEOP state, slave refused state change

[Richard Hacker]

Hi Joachim

Please send the output of the following commands:
# ethercat rescan
# ethercat sl -v
# ethercat pdos
# (start your application and keep it running for the next command)
# ethercat config -v

Maybe you can try to enable watchdog (although it is reported 
differently in the SII):

     {2, EC_DIR_OUTPUT, 1, slave_0_pdos + 0, EC_WD_ENABLE},

You could also have a look at the documentation to see whether there are 
any output PDOs (RxPDO) that are mandatory.

Richard

------------------------------------------------------------------------

On 9/18/20 7:20 AM, Joachim Sällvin wrote:
> Hi,
> 
> My AKD drive slave refuses to go to operational. Any suggestions why?
> 
> This is what dmesg tells me when trying:
> [53271.293863] EtherCAT ERROR 0-0: Failed to set SAFEOP state, slave refused state change (PREOP + ERROR).
> [53271.294126] EtherCAT ERROR 0-0: AL status message 0x001D: "Invalid output configuration".
> 
> The AKD drive is the only slave on the bus
> $ sudo ethercat slaves
> 0  901:0  PREOP  E  AKD EtherCAT Drive (CoE)
> 
> and I've configured it so that I get
> 
> $ sudo ethercat cstruct -p0
> /* Master 0, Slave 0, "AKD"
>   * Vendor ID:       0x0000006a
>   * Product code:    0x00414b44
>   * Revision number: 0x00000002
>   */
> 
> ec_pdo_entry_info_t slave_0_pdo_entries[] = {
>      {0x6040, 0x00, 16},
>      {0x60c1, 0x01, 32},
>      {0x6041, 0x00, 16},
>      {0x3470, 0x04, 16},
>      {0x60fd, 0x00, 32},
>      {0x606c, 0x00, 32},
>      {0x6063, 0x00, 32},
> };
> 
> ec_pdo_info_t slave_0_pdos[] = {
>      {0x1600, 2, slave_0_pdo_entries + 0},
>      {0x1a00, 3, slave_0_pdo_entries + 2},
>      {0x1a01, 2, slave_0_pdo_entries + 5},
> };
> 
> ec_sync_info_t slave_0_syncs[] = {
>      {0, EC_DIR_OUTPUT, 0, NULL, EC_WD_DISABLE},
>      {1, EC_DIR_INPUT, 0, NULL, EC_WD_DISABLE},
>      {2, EC_DIR_OUTPUT, 1, slave_0_pdos + 0, EC_WD_DISABLE},
>      {3, EC_DIR_INPUT, 2, slave_0_pdos + 1, EC_WD_DISABLE},
>      {0xff}
> };
> 
> 
> 
> I've tried with the command line tool...
> $ sudo ethercat states OP
> 
> ..and with my c-application. But the result is the same.
> 
> One thing that puzzles me is the size of the synch managers SM2 and SM3:
> 
> $ sudo ethercat pdos
> SM0: PhysAddr 0x1800, DefaultSize 1024, ControlRegister 0x26, Enable 1
> SM1: PhysAddr 0x1c00, DefaultSize 1024, ControlRegister 0x22, Enable 1
> SM2: PhysAddr 0x1100, DefaultSize    0, ControlRegister 0x24, Enable 1
>    RxPDO 0x1600 ""
>      PDO entry 0x6040:00, 16 bit, ""
>      PDO entry 0x60c1:01, 32 bit, ""
> SM3: PhysAddr 0x1140, DefaultSize    0, ControlRegister 0x20, Enable 1
>    TxPDO 0x1a00 ""
>      PDO entry 0x6041:00, 16 bit, ""
>      PDO entry 0x3470:04, 16 bit, ""
>      PDO entry 0x60fd:00, 32 bit, ""
>    TxPDO 0x1a01 ""
>      PDO entry 0x606c:00, 32 bit, ""
>      PDO entry 0x6063:00, 32 bit, ""
> 
> Should they really have DefaultSize 0?
> 
> $ sudo ethercat versionIgH EtherCAT master 1.5.2 53ce5e56d511
> $ uname -a Linux ctrlPC1 5.4.54-rt32 #1 SMP PREEMPT_RT Wed Aug 12 12:59:33 CEST 2020 x86_64 x86_64 x86_64 GNU/Linux
> 
> 
> 
> Detailed dmesg printout:
> 
> 
> [54154.149923] EtherCAT: Master driver 1.5.2 53ce5e56d511
> [54154.149991] EtherCAT: 1 master waiting for devices.
> [54154.154118] ec_generic: EtherCAT master generic Ethernet device module 1.5.2 53ce5e56d511
> [54154.154127] EtherCAT: Accepting 78:D0:04:27:52:E4 as main device for master 0.
> [54154.154131] ec_generic: Binding socket to interface 4 (enp0s31f6).
> [54154.189154] EtherCAT 0: Starting EtherCAT-IDLE thread.
> [54154.189384] EtherCAT 0: Link state of ecm0 changed to UP.
> [54154.197141] EtherCAT 0: 1 slave(s) responding on main device.
> [54154.197149] EtherCAT 0: Slave states on main device: PREOP.
> [54154.197613] EtherCAT 0: Scanning bus.
> [54154.489005] EtherCAT 0: Bus scanning completed in 292 ms.
> [54154.489006] EtherCAT 0: Using slave 0 as DC reference clock.
> [54154.489007] EtherCAT 0: Starting EoE thread.
> [54154.521934] EtherCAT ERROR 0-0: Failed to set SAFEOP state, slave refused state change (PREOP + ERROR).
> [54154.522227] EtherCAT ERROR 0-0: AL status message 0x001D: "Invalid output configuration".
> [54154.525166] EtherCAT 0-0: Acknowledged state PREOP.
> 
> 
> Any ideas?
> 
> Best Regards,
> 
> Joachim Sällvin
> 
> Software Developer
> CorpowerOcean
> 
> 
> 
> 
> 
> 
> 
> 
>