[etherlab-users] install on non-PC

[Jeff Krasky]

Here is the output of dmesg.  Maybe the problem is the EtherCAT code still
expects a supported network card driver and hardware, whereas the board
hardware has a network interface that EtherCAT isn’t familiar with?

 

# dmesg

Linux version 2.6.33 (user1 at dhcppc15) (gcc version 4.3.5 (Buildroot 2011.05)
) #

1 Fri Nov 18 03:41:18 CST 2011

CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

CPU: VIVT data cache, VIVT instruction cache

Machine: Atmel AT91SAM9G20-EK

Memory policy: ECC disabled, Data cache writeback

On node 0 totalpages: 16384

free_area_init_node: node 0, pgdat c032d690, node_mem_map c034c000

  Normal zone: 128 pages used for memmap

  Normal zone: 0 pages reserved

  Normal zone: 16256 pages, LIFO batch:3

Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1
mtdparts=at91_nand

:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root)
rw

rootfstype=jffs2

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 64MB = 64MB total

Memory: 61524KB available (2900K code, 233K data, 124K init, 0K highmem)

Hierarchical RCU implementation.

RCU-based detection of stalled CPUs is enabled.

NR_IRQS:192

AT91: 96 gpio irqs in 3 banks

Console: colour dummy device 80x30

console [ttyS0] enabled

Calibrating delay loop... 197.83 BogoMIPS (lpj=989184)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

AT91: Power Management

AT91: Starting after general reset

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Advanced Linux Sound Architecture Driver Version 1.0.21.

Switching to clocksource pit

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

NetWinder Floating Point Emulator V0.97 (double precision)

JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.

msgmni has been set to 120

io scheduler noop registered (default)

atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL

atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL

atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL

brd: module loaded

loop: module loaded

ssc ssc.0: Atmel SSC device at 0xc4878000 (irq 14)

NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V
8-bi

t)

AT91 NAND: 8-bit, Software ECC

Scanning device for bad blocks

Creating 3 MTD partitions on "atmel_nand":

0x000000000000-0x000000400000 : "Bootstrap"

0x000000400000-0x000004000000 : "Partition 1"

0x000004000000-0x000010000000 : "Partition 2"

atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)

macb macb: invalid hw address, using random

MACB_mii_bus: probed

eth0: Atmel MACB at 0xfffc4000 irq 21 (be:b0:6c:d8:c9:a9)

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00,
irq=-1)

usbmon: debugfs is not available

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

at91_ohci at91_ohci: AT91 OHCI

at91_ohci at91_ohci: new USB bus registered, assigned bus number 1

at91_ohci at91_ohci: irq 20, io mem 0x00500000

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

udc: at91_udc version 3 May 2006

mice: PS/2 mouse device common for all mice

input: gpio-keys as /devices/platform/gpio-keys/input/input0

rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0

IRQ 1/rtc0: IRQF_DISABLED is not guaranteed on shared IRQs

rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!

Registered led device: ds5

Registered led device: ds1

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

ALSA device list:

  No soundcards found.

TCP cubic registered

NET: Registered protocol family 17

rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock

Empty flash at 0x00292afc ends at 0x00293000

jffs2_scan_inode_node(): CRC failed on node at 0x002997dc: Read 0xffffffff,
calc

ulated 0x40d08aa9

Empty flash at 0x00299828 ends at 0x0029a000

VFS: Mounted root (jffs2 filesystem) on device 31:1.

Freeing init memory: 124K

JFFS2 notice: (1) check_node_data: wrong data CRC in data node at
0x0029c438: re

ad 0x34ff28d, calculated 0xa7e7ac32.

#

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.etherlab.org/pipermail/etherlab-users/attachments/20111122/21db317b/attachment-0004.htm>